User ManualANALOG/DIGITAL, POSTIONER RECEIVER WITHEMBEDDED VIACCESS AND COMMON INTERFACE
TV ANTENNA TVRF IN9Receiver to TV with Audio and Video RCAs VIDEO AUDIO IN INReceiver to TV and VCR with SCART Cables1. Connect th
10Receiver to TV, VCR and Decoder with SCART CablesDECODER DECODER SCART1. Connect the Off-air TV antenna or cable if available to the ANT IN socket
11One Actuated Dish1. Connect the IF OUT and LNB IN connectors using the loop through cable provided with the EchoStar AD-3000IP VIACCESS.2. Connect t
12Two Fixed Dishes using DiSEqC mode1. Connect the IF OUT and LNB IN connectors using the loop through cable provided with the EchoStar AD-3000IP VIAC
A. Receiver and TV set-upCheck the InstallationTo get the most out of the EchoStar AD-3000IP VIACCESS it should be correctly installed, the dishshould
14Move the dish a few counts to the west by pressing the key and press the OK key to store east limit in this position. The indicated number will be
Go back to the Satellite option using the key.Now press the or key to select the mosteastern satellite you can receive.Press the OK key.Select t
16Go in to the “Motorized dish setting” menu with the key to “Erase Position Data” and press the OK key. Then go to “EraseAll Satellite Data” press
User’s Setting17Local Time SettingUser’s Settings are only accessible via the Installation screen.Language SettingSubtitleNoneEngItaSubtitleSelect the
Please select your TV format.4:3 for normal screen TV16:9 for wide screen TVAspectA/V Output Setting18About EchoStarYou can see the details of the com
CONTENTS3.4. Remote Control Unit (RCU) ------------------------------------------------------- 75. Getting started ------------------------------
19InstallationB. Main menu and InstallationPress the MENU key to display the “Main Menu” on the screen.Main MenuSelect a sub-menu using the , keys
Note: To stop searching press the key on theUsing the Auto Search option, the EchoStar AD-3000IPVIACCESS searches for all available channels(R
21Parental ControlWith parental control it can be prevented that a TV channel can be watched, a Radio Channel canbe heard, the receiver settings can b
22If the Installation & Edit Lock is [ON], you have to input the correct code to enter directly into the “Installation” and “Edit” menu..Press th
23Edit Radio ChannelUse the same procedure for the Radio Channels as used for editing the TV Channels as above.You can move to the channel that you wa
24Edit SatelliteTo delete a transponder, press the red key when thehighlighted bar is located at the transponder youwant to delete.To add a transponde
25ALT AudioIf more than one audio channel is provided bythe broadcaster on a specific channel, you canactivate the audio mode display by pressing the
26Note 1) You should execute “Auto Search” after editing the satellite or the transponder. If “Auto Search” is executed after adding the
You can edit up to 8 local frequencies by using numerickeys.And if you want to save the newly edited frequency, press the OK key.27If you want to rese
28 1. Tuner & channel Input connector 1 x F type with loop through Output connector 1 x F type 75 Ohm Frequency range 950MHz to 2150MH
WARNING!Always follow these instructions to avoid the risk of injury to yourself or damage to your equipment.Unplug the receiver from the AC power out
29 S/PDIF out RCA x 1 Analog audio out RCA x 2 (L-Ch x 1, R-Ch x 1), SCART x 2 (TV, VCR)Resolution 16bit DACOutput level 2Vrms max.Volume
30 1. RF Input frequency range 900MHz to 2150MHz Input impedance 75 Ohms IF bandwidth 27MHz IF frequency 479.5MHz Input signal lev
2. Features 1. Satellites : up to 50 satellites, 999 transponders 2. 4-digit 7-segment LED on the front panel displays channel information 3. Dis
1. MPEG-2 Video (MP@ML) 2. MPEG-1 Audio layer 1, layer 2 3. MPEG-2 Digital & fully DVB compliant 4. Viaccess embedded with 1 smart card 5. C
Front PanelFront Panel3. Front & Rear ViewRear PanelRear Panel5AC power cordRF output connector to TVAntenna inputLNB inputLoop throughNote: All
Smart Card and CI ModuleTo watch payable program channels, a CI module and a smart card from the service provider is necessary.(The service provider i
4. Remote Control Unit (RCU)7The Power key turns the receiver on and off.The LED (Light Emitting Diode) flashes red to show the remote is working. The
DO NOT PLUG the receiver into Main Power Outlet, until you complete all the connections to the receiver.DO NOT PLUG the receiver into Main Power Outle
Komentáře k této Příručce